Is there a lot to learn about woodworking? You just cut some wood, sand it down and nail it together, right? There is much more than that in the hobby. The following article offers many tips to help you start woodworking.

As with anything involving power tools, safety is the number one concern in woodworking. Wear safety equipment and always use tools the correct way. Always keep the tool guards on, since they are there to keep you safe. You don’t want to go to the hospital because you did something stupid.

Always apply a pre-stain conditioner to the wood you want to stain. Using this conditioner will reduce the amount of blotching or unevenness on your finished project. Conditioners can smooth the uneven grain of your wood and cause the stain to penetrate the wood more evenly.

TIP! Use a pre-stain wood conditioner before applying a stain. This will reduce any blotches in the piece that you create.

When you apply wood finishes and stains, make sure you stir, not shake them. Stains often have ingredients that settle to the bottom. Shaking can lead to bubbling, though, which causes its own set of problems. Make sure that the product is thoroughly stirred, and everything is evenly dispersed.

Always do a dry fit prior to gluing two pieces of wood together. If you don’t and then try to do adjustments, chances are you’ll create damage to your project. A dry-fit will give you a good idea of what components go where.

Keep a ruler inside your pocket, and make sure it stays put. Try switching to a metal ruler, keeping it in a pocket with your telescoping magnet, the kind used to reach and pick up screws or nails. This will hold the two together, making them bulking enough to stay put.

Always stir your stains instead of shaking. Ingredients may have settled onto the bottom as they sat on the shelf. However, shaking can cause bubbling and prevent a thorough mixing of the product. Stir the mixture thoroughly.

Screw Holes

If you have interior doors that are starting to come loose, you can easily remedy this problem with golf tee. Start by removing the door from the frame. Remove the hinges too and tap tees into the screw holes. Cut the part of the tees that do not fit into the screw holes before putting the door back in its frame. The golf tee allows a screw to have something it can bite into.

Choose the correct nails when starting a project. If you use a nail whose diameter is too great, it can split the wood, which causes it not have a proper hold. However, very small nails do not penetrate the wood well; therefore, it won’t hold the wood properly. So, it is important to determine the correct size nail for the job.

Add a stair gauge to the shop that you create. This is used for laying out stair jacks and can also be used to clamp a carpenter’s square. It will convert a carpenter’s square into your guide for the circular saw. Using the square can help you get straight cuts each time.

TIP! Each shop needs a stair gauge. They are most often used to layout stair jacks, but you can use them to clamp your carpenter’s square.

Do you have screws that are out of reach that need tightened, but you can’t fit a screwdriver or your hand in the area? You can solve this problem. Just grab a 12-point socket set. Place the socket on your screwdriver, then use it on the ratchet.

Keep your work area well lit. Woodworking involves accurate measurements. Not being able to see your tools when you use them can be detrimental. Make sure the room is well-lit to eliminate injuries and mistakes.

Be on the lookout for people that want to sell their house. You may be able to increase the value of your house with your skills. It is possible to build new mailbox posts, refurbish cabinetry and perform all sorts of useful projects around the home.

Know wood characteristics before buying or using it in your projects that need staining. Paint grade wood is generally of lower quality and stain grade has better grain patterns. If using veneer or particleboard, understand that particleboard absorbs a lot of stain while veneer will not absorb as much. The proper wood helps your project come out the way that you hoped.

TIP! Know all about the wood you are getting prior to purchasing it, especially if you plan to stain it. You’ll want to look for paint-grade or stain-grade woods, depending on your desires for the project.

Your eyes are exposed to possible danger when you are working on a project. Therefore, always wear your goggles to avoid an accident. If they do not fit that well or give clear eyesight, get a pair that do.

Certain hand tools are a must for the shop. A hammer ought to be the first tool. The best type of hammer for woodworking is a claw hammer. Get one with the proper heft for your hand. You won’t want to be using a hammer that weighs too much.

Always wet a surface before beginning to sand. Water raises the grain on the surface of the wood. That allows you to get rid of even small scratches. This makes your final product look better. It can also save you a bit of work in the future.

Keeping a little ruler inside your pocket is smart, but it could fall out when bending over due to its length. Purchase one that is made of metal and place it inside the same pocket where you keep your telescoping magnet. The magnet will keep the ruler safely in your pocket.

TIP! It is handy to carry a small pocket ruler, but it may fall out whenever you bend over. To reduce this problem, you could get a metal ruler and put the ruler in the same place as where you store your magnet.

Double check every measurement. Triple checking might even be a good idea if you’re using materials that are expensive. Measuring is where a lot of people make mistakes. If you make a wrong cut, it can totally ruin a project.

Patience is paramount. It’s easy to start a project, become frustrated, and quit because results are not instantaneous. Remember that your result is waiting there inside of the wood, you just have to bring it out. Keep patient and stay focused. Most importantly, keep working! In no time, your work will be complete.

Be sure to draw up some plans before beginning a woodworking project. If you start out with a budget and blueprint for the entire project, this helps to keep you in check as you’re working on it. Also, it will help you to reduce the amount of wood that you waste. Plan things ahead so that the projects go smoothly.

Sturdy footwear is essential when woodworking. Your feet need to be protected from stepping on nails or having tools dropped on them. It is important to always protect your feet. Injury can happen if you drop a heavy tool, kick something heavy, or step on a sharp object. Sturdy shoes with toe protectors can prevent work related accidents.

TIP! Footwear is an important component of your safety equipment. You’ll have wood pieces, nails, and tools all over the place.

Try making your own sanding blocks. Just cut blocks of wood into the specific size and shape needed. After that, use adhesive to attach the block to the sandpaper, and let it dry. Now you have a new sanding block that is the ideal size for the wood project at hand.

Make sure that your tools are of the best quality. Tools that are cheap can break and cause major frustrations. Good tools cost more, but will last a very long time if you care for them properly. In the long run, investing in good tools is an economical choice.

Now, do you have a better understanding of all the intricacies of woodworking? Start learning how woodworking can benefit you. From doing woodworking as a hobby, or as a job that’s full time, this knowledge is going to help you push the limits well into the future.

Seek out wood that has been recycled. Many places have scrap wood that you can use. You may be surprised to learn that many home improvement stores or other types of businesses that use wood will simply throw out any wood they don’t use. This is where you should jump at the chance to get some extra wood for your own projects. You will save on materials as well.