If you’ve always desired working with wood, you aren’t alone. A lot of people wish to get into working with wood, but they’re not sure of where to begin. Your luck is about to take a turn. This article has everything you should know about woodworking. Continue reading to gain a good understanding of the craft.

If you plan to stain a project, apply pre-stain products to your wood. A pre-stain conditioner helps keep away any irregularities or blotches in the wood. They smooth the wood, allowing the stain to set correctly.

For crosscut guides use a stair gauge. To use, clamp the gauges to a carpenter square. Then you simply mark where the notches are. By placing them on the tongue of the carpenters square that is the same, you can come up with a very good guide for the circular saw.

TIP! Use stair gauges to guide your crosscuts. Just clamp them on your carpenter’s square while making sure they match up.

Test your stains on scraps of wood or inconspicuous areas of the piece you’re using. This ensures that the stain will look as you expect it to once done. Keep in mind that it is not easy to guess how wood stain will turn out; therefore, you should always test out the stain on a piece of wood to prevent disappointment.

Try using stair gauges for your crosscut guides. Attach them to a carpenter’s square, and use them to ensure that they match the rise and run of your stair jack. Then you simply mark where the notches are. If they’re on the same carpenter square’s tongue, that combination can create the perfect guide for a crosscut using a circular saw.

Prepare your finishes and stains by stirring them instead of shaking them. The ingredients can settle eventually. Shaking can make it have bubbles and it won’t mix well. Stir it well and you shouldn’t have an issue.

Before using any stains or finishes on your wood, make sure you stir them and not shake them. There are ingredients in these types of products that can settle over a period of time. But, if you shake it could cause bubbles to form which would mean it wouldn’t mix too well. Make sure that the product is thoroughly stirred, and everything is evenly dispersed.

TIP! When you’re using finishes or stains you should always stir them instead of shaking them. Some of the ingredients in these stains and finishes tend to settle to the bottom over time.

Buy nails in the right size and of the right material for each job. Any nail that is way too big in its diameter will split your wood a lot of the time and that makes it not hold right. On the other hand, a nail that is too small will not penetrate and hold the wood together. Always try to pick the right size nail for your job.

Look around your neighborhood and workplace for sources of free wood. You can likely get pallets from businesses as long as you haul them away. Look online for some more ideas.

Be very careful when working with a table saw. When you are crosscutting, be sure to set the length of the cut using a block that is clamped onto the fence. This is safer and prevents board movement. Clamps leave the end of the board free to cut.

Account for new tools in your budget. This can be easy to neglect, since you might just be focusing on the cost of the wood. However, if you have to get tools that you do not have, this can break your budget.

Bird Feeder

Enjoy your yard more thanks to your woodworking abilities. You can build yourself something like a deck along with a bird feeder. You can then relax on that deck, virtually bug free, as you watch all the birds you have attracted to your bird feeder have a picnic of their own. If you work with wood professionally, show them your projects so they can see some examples.

Make your own reusable sanding block. Although sanding blocks provide you with more control while sanding, this doesn’t mean you should spend a lot on sandpaper holders. Use some scrap plywood for making your own. Cut some scrap wood for every sandpaper grit you have, spray adhesive on it and then apply the sandpaper.

If you need to rent a tool for woodworking, lease one from a tool company and ask them how to use it. In most cases, a specialist will show you how to properly use the tool you want to rent. Also ask if they have a user’s guide for it.

Stair Gauge

You can use a stair gauge to guide circular saws. Normally you use a stair gauge to figure out the run and rise of your stair jack which can allow you to get the notches matched up. By attaching them to a carpenter’s square, you can use them for circular saw cuts instead.

Always check your measurements a couple of times. Triple checking might even be a good idea if you’re using materials that are expensive. Measuring can cause big mistakes. A small error can easily be the death of a large piece of wood, so be sure to check and then check again every time.

Whenever you’re thinking of cutting a piece of wood that’s narrow, don’t try to use your fingers to guide it. Use a strip of wood instead to maximize safety. This helps you keep every finger, which are required for doing future woodworking.

TIP! When cutting a narrow wooden piece, do not use fingers like guides! What you should do instead is use a thin, long strip of wood that will help you push the wood through. This will help to keep you from cutting off your fingers, which would be a travesty.

Have some patience. It’s easy to start a project, become frustrated, and quit because results are not instantaneous. Know that you need to work hard at getting your piece from the wood you’re working on, and to do that you need patience. Patience will help you stay focused on your project. You’ll be making great pieces in no time!

You can make sanding blocks on your own. To make a sanding block cut a piece of wood to a size that fits comfortable in your hand. Tape the sandpaper on the block with adhesive. You’ll end up with a perfectly sized sanding block.

If you are thinking about a big project, it might be best that you take a look at what other people have created. While you may not follow them exactly, they give you a springboard off which you can create your own plans. This can lead to a more efficient project and help with planning everything out so it all runs much smoother.

Keeping a small ruler inside one of your pockets is a great idea, but it could fall out due to its size. To reduce this problem, you could get a metal ruler and put the ruler in the same place as where you store your magnet. The magnet keeps both objects firmly in your pocket.

TIP! You should have a small ruler on you. Make it a metal ruler and store it alongside your telescoping magnet.

You should not get started on a project before getting a good idea of how you will complete it. You could make mistakes by only reading the instructions once. Read the directions several times to be sure that you understand them.

Think long term at all stages of your project. If you are building a backyard woodshed, for instance, keep in mind you may want to add electricity later. If that is the case, you have to think about where switches and wiring will be placed, among other things.

Don’t purchase too many hardware, tools, or wood. Quite often bulk buying means bulk inventory that just sits around taking space. Just buy what you need for the current project.

Use the right-sized nail for the project. Very large nails can cause wood to split, which will prevent it from holding well. Conversely, if the nail is too small, it can’t penetrate deep enough in the wood to hold these pieces of wood together. Always try to pick the right size nail for your job.

TIP! You want to be sure that you have the right size nails for your project. Nails that are too big can split the wood.

As you are now aware, woodworking is a talent that you can develop. There are many benefits when you create a piece of art with wood. Whatever you choose to create, you should now have enough information for you to get through the process. You can go ahead and make the birdcage you have been dreaming of. So what if you do not own a bird or pet?