Woodworking is a highly-desired skill that is always in demand. Woodworking has a number of fascinating aspects, making it accessible and interesting to everyone, regardless of skill. The following paragraphs are full of ideas you can use to be a better woodworker.

You can make your own reusable sanding blocks. Make a list of each sandpaper grit that you typically use, and then cut a full six blocks for each from scrap plywood, 3/4″ thick. They should be 2.5″ by 4.75″. Use a spray glue on the blocks and the tile square. Put one block on the tile square and cut the cork with a utility knife. Spray adhesive on your sandpaper, and then stick it to every cork block, facing down. You can make smaller blocks if you wish as well. These can be used for smaller pieces demanding finer sanding.

Try out some gel stain next time you are staining furniture items. Liquid stains have a tendency to run but gel stains will stay in place better, without running. The thickness of gel stains helps because it allows the pigment to distribute evenly over all different types of wood pieces.

Workbench Height

Do you realize that your workbench height is key to the success of your projects? If you wish to determine your ideal workbench height, measure how far it is from the floor to the middle of your waist. That tells you the best height for a good workbench.

Select an appropriate sort of wood for each project. Some woods are not as strong as others. If you don’t know how each wood type reacts to what you’re trying to do, spend a bit of time learning about it.

Your woodworking shop needs a stair gauge. Typically, they are used for the layout of stair jacks, but they can also be used to clamp down the carpenter’s square. You can then use the square as a handy guide for your circular saw. This will help you with making straight cuts each and every time.

Gel Stains

If you plan to stain furniture, look in to gel stains. Liquid-based stain often runs on application, and gel stains stay put much better. In addition, the thicker consistency of gel stains have more consistent pigments and allow for a more even coat of stain on vertical and horizontal pieces.

Use tin snips to cut laminate that you are using for your projects. Tin snips will let you easily turn the laminate into a more usable size. Getting a set of tin snips you’ll only use for laminate will keep your snips sharp.

Understand the properties of the wood you’re using. Each type of wood has different traits. Different trees respond differently to staining. Different cuts of wood will also splinter differently. In addition, the grain will look different as well. These will all factor into your woodworking plans.

TIP! Know your wood. Keep in mind that all wood has different characteristics.

A stair gauge is a great tool to keep in your shop. Commonly used to scribe stair jacks, it can also be used to attach to your carpenter’s square. This can make a carpenter’s square serve as a guide for a circular saw. When you use this square, you’ll cut perfectly straight every time.

Know all about the wood you are getting prior to purchasing it, especially if you plan to stain it. Lower quality wood will be called paint grade. Stain grade will be of higher quality and have a nicer finish. Veneer and particleboard are different too. Veneer doesn’t absorb stain and particleboard absorbs more. Choosing the right wood turns your project into a success.

Learn the characteristics of different kinds of wood. Each wood has its own characteristics. Different trees respond differently to staining. The cuts could differ in splintering and effects. The variety of different wood grains is astonishing. This is something that you must consider before beginning your project.

You can use a golf tee to help tighten up the hinges of an interior door. Remove the hinges and the door. Then, in the hole where the screws were, lightly hammer a common golf tee into the hole. Cut the part of the tees that do not fit into the screw holes before putting the door back in its frame. This will give the screw the support that it needs.

TIP! If your door hinges are loose, you can use a golf tee to fix them. Take the door and hinges off the frame, and lightly hit a golf tee down into every screw hole.

Look around for wood that is recycled. Numerous places that sell or work with many types of wood will often discard the scraps which are useful to you. Many places like home improvement stores will have scrap wood. Look for pieces of wood that you can use in your projects. This will also be a great way to save some money.

Always practice safety when using a table saw. While crosscutting, it is important that you use a block properly secured on the fence when establishing the cut length. This is preferred over just using the fence alone, because it prevents your board from springing back. Using this clamping method will allow the board end to still be cut.

Stair Gauges

Wear ear protection. A wood shop can be extremely noisy. Exposure over a long period of time can be bad on your hearing. Get a pair of inexpensive ear plugs, or buy a great pair of noise canceling headphones. Make sure you wear them when working with woodworking tools.

TIP! Make sure to properly protect your ears. The machinery used can get very loud.

Stair gauges can be used as circular saw guides. Typically, stair gauges are used to calibrate stair jack rises and runs. However, using both on the carpenter square tongue, you will have a useful guide when using the circular saw.

It’s no shock to learn woodworking is a hobby and skill that has lasted for many years. Since the dawn of time woodworking skills have been in high demand. No matter if you’re a fanatic or just a hobbyist on the weekends, the tips above should help you enjoy this art more.