This article is for you if you want to get into the wonderful world of woodworking. Lots of tips are included below to get you going on this fantastic hobby. Keep reading if you want to learn more about this wonderful art form.

Always make safety first with a woodworking project. Always use your tools in the way they were intended to be used and wear safety equipment at all times. Avoid taking off the guards on power tools; they are meant to protect you. If you end up hurt, you won’t be able to work at all.

Safety must be a priority when doing woodworking. Always purchase the necessary safety equipment to avoid injury. Never remove any guards off of your power tools that are there to protect you. The last thing you want is to injure yourself severely while woodworking.

TIP! Safety is the most important aspect of a project. Always start a job with the proper safety gear and follow instructions for using the tools properly.

When using stain, try a test on a small scrap you may have available or in an area on the wood that will be out of sight. This way you will avoid any surprises in case the color of the stain looks different after application. Wood can be unpredictable, so you can avoid mistakes and disappointment by doing this simple test.

A great tool for setting crosscut guides is a stair gauge. Clamp them on the carpenter’s square. Then mark the notches. When you clamp them on the one tongue of the carpenter’s square it will become a good crosscut guide for your circular saw.

Choose the right size of nail for your project. Any nail that is way too big in its diameter will split your wood a lot of the time and that makes it not hold right. However, too small of a nail will not penetrate deep enough to keep the wood held together. Make sure you get nails that are just right.

Were you aware that your workbench height makes a difference in your quality of work? To determine the right height, measure between the floor and the middle of your own waist. That tells you the best height for a good workbench.

TIP! How high your workbench is truly affects the quality of your work. Starting from your waist midline, measure the distance down to the floor; this is your ideal workbench height.

Add some extra spring to your grip. A spring clamp may be useful sometimes, but only if you can use more than one hand. It is sometimes hard to get these things open when you’re only using a single hand. However, it can be made easier. Before you start gluing anything, take the time to clamp a separate wood piece so that the clamps are already open. This makes opening them with one hand unnecessary.

Make sure to purchase and wear proper ear protection. Woodworking equipment can be very noisy. Exposing your ears to these things for a long time can cause hearing loss. Use a pair of high quality headphones or disposable earplugs. No matter what you choose, be sure that you use them whenever you operate machinery.

If you are just starting a project, make sure to read the plans many times. You should fully understand everything that you will need to do. If they are hard to understand or are missing information, seek assistance.

You should understand that stains should be stirred, not shaken up. Stir often because these stains settle over time. But, shaking may cause unwanted bubbling, and keep the product from mixing well. Stir thoroughly until it is even.

TIP! Stir finishes or stains before using them. Some ingredients they contain will settle at the bottom of the can, which can effect the outcome of your project.

Make sure you get the right type of wood. Don’t use woods that are soft like pine when making a table top; soft woods scratch easily. Remember that different varieties of wood have different colors when they are finished.

Always employ safety practices when using a table saw. If you are making a crosscut, set the length for the cut by clamping a block to the fence. This is safer than just using the fence directly, as it prevents the wood from kicking back. This clamping method leaves the end of the board accessible for cutting.

Turn your yard into an oasis through woodworking. You can build things like a beautiful deck, and a place to feed birds. The birds that visit will keep insects away while you work on your next project. If woodworking is something you want to do professionally, have client meetings on a deck you built so they personally see your work.

One of the more recent developments in stains are gel stains. Liquid tends to run after it’s put on, whereas a gel stain sticks to the wood much better. Also, gel stains are thick, so they tend to stain more evenly.

TIP! Gel stains are an excellent choice for furniture staining. Liquid stains are prone to running, while gel stains tend to stick.

Keep an eye out for used furniture that you could pick up. People can be throwing away furniture that you can get wood from for free. Consider what you can do before you dismiss anything. You may be able to salvage the drawers of an unusable dresser and re-purpose them as bookshelves.

You shouldn’t be applying too much pressure when sanding. Pressure can cause you to get uneven results, or might gauge the surface. Choose a sand paper that has the right grit, because you aren’t going to have to use excessive force to use it. Lightly sand with a circular motion and you’ll be fine.

Consider reusing your sanding block. This makes it easy for you to control the sanding and also isn’t as hard on your hands. It is easy to use scrap wood to make one. Cut one wood scrap for each sandpaper grit, and then spray it with adhesive and attach the sandpaper.

Every shop that does woodworking needs to contain a stair gauge. Commonly used to scribe stair jacks, it can also be used to attach to your carpenter’s square. This can make your carpenter’s square into a guide for your circular saw. Using the square can help you get straight cuts each time.

TIP! You need a good stair gauge in your shop. They not only assist with stair jack layouts, but can also be used when your carpenter’s square needs to be clamped.

Do not build a tangle of extension cords, just stick to one when woodworking. Correct use means unplugging a tool when you finished with it and plugging in the next one you will be using. By following this tip, you can prevent accidentally tripping and possibly being electrocuted.

As you may have already figured out, there is more to woodworking than meets the eye. Thankfully, these tips will help you achieve that. The only thing left to do is put the above advice to use.