It can be quite exciting to get started with woodworking. You can create nearly anything out of wood. Man has utilized wood for thousands of years. It’s rarely an easy feat, but there are good number of techniques and tricks you can apply along the way. With enough practice, you’ll be building spectacular pieces that you’re proud of.

Condition your wood with a pre-stain product. You will get less irregularities or blotches if you apply a quality pre-stain product. They will make the wood smooth and allow the stain to go on evenly.

Pre-stain conditioners are very important to use while woodworking. Using a pre-conditioner will help you avoid blotches when staining. This is because the conditioners allow stains to penetrate evenly.

TIP! Always apply a pre-stain conditioner to the wood you want to stain. Using this conditioner will reduce the amount of blotching or unevenness on your finished project.

Make your own sanding blocks. You will need three-quarter-inch plywood cut into six blocks. Be sure to create a block for each of the sandpaper grits you typically use. Try to be certain that they measure roughly 2.5 inches by 4.75 inches. Apply spray adhesive to both the blocks and the cork tiles. Stick a block to the cork, making sure to cut the cork flush with a utility knife. Put adhesive on the sandpaper sheet and then apply it to the cork blocks face down. Cut the sandpaper flush and label the block.

If you plan to use stain, test it on a small scrap of wood first. This lets you stay away from any sudden surprises when the stain color is not what you expected. Wood is unpredictable at times and you should do this test so that you aren’t disappointed by the results.

Workbench Height

When you apply wood finishes and stains, make sure you stir, not shake them. Stains often have ingredients that settle to the bottom. Shaking can cause bubbling and prevent it from mixing well. Stir as best as you can to prevent this from happening.

TIP! When using stains or finishes, be sure to stir them, rather than shake them. It is possible that some of the ingredients will settle as time goes on.

Are you aware that your workbench height is essential for having successful woodworking projects? In order to attain the perfect workbench height, first measure how far it is from the middle of your waist to the floor. This lets you know what the best height is for your workbench.

Different projects will require different types of wood. Not all woods are equal. If you aren’t sure how a wood type will respond to your project plans, then you should research the wood before you begin.

Before applying glue, try a dry fitting first. If you attempt to readjust the pieces once glued together, you risk damage to your project. You can figure out what goes where with a dry fit.

Refrain from putting your fingers near your cut. Instead, push the pieces through your saw with a long strip of wood. This technique helps protect your fingers from injury.

TIP! Whenever you plan to cut a narrow piece of wood, don’t use your fingers as a guide! The smart thing to do is to use another wood piece to push your wood up to the saw. This will help to keep you from cutting off your fingers, which would be a travesty.

You need a stair gauge inside your workshop. This is used for laying out stair jacks and can also be used to clamp a carpenter’s square. By doing this, your carpenter’s square can turn into a circular saw guide. You can have straight cuts every single time when you use that square.

While you might like keeping a small ruler handy in your pocket, you probably find that it falls out every time you bend over. Get yourself a ruler made of metal and put it in the pocket where you store your telescoping magnet. The magnet should keep your ruler in the pocket.

Use these tips to make your woodworking skills better. There is always something new to learn, so remain open to learning more. Never let any woodworking project deflate you in any way because it takes time to get better.

Each shop needs a stair gauge. They are used often to layout jacks for stairs, but they can also be clamped to your carpenter’s square. You can then use the square as a handy guide for your circular saw. When you use this square, you’ll cut perfectly straight every time.