You are not the only one who has the desire to create something out of wood. Lots of people wish they could work using wood, but lack the know-how. Get ready! Your world is getting ready to change. This article contains a lot of useful information. Continue reading to gain a good understanding of the craft.

Test your stains on scraps of wood or inconspicuous areas of the piece you’re using. If you test the stain color first, you will not have any unpleasant surprises. Wood is unpredictable at times and you should do this test so that you aren’t disappointed by the results.

If you plan on staining your project, try using pre-stain conditioner on your wooden surfaces. Using this conditioner will reduce the amount of blotching or unevenness on your finished project. It will also help to improve the appearance of the wood itself, as wood has a natural grain and the conditioner fills it in to some degree.

TIP! Pre-stain wood conditioners should be used prior to staining any wood project. Using this conditioner will reduce the amount of blotching or unevenness on your finished project.

Gel stains are a good way to stain furniture. Liquid stains have a tendency to run but gel stains will stay in place better, without running. Also, since these gel stains have a thicker consistency, their pigment stays consistent during the whole application process which shows in the even staining on both horizontal and vertical surfaces.

Grade Refers

Get to know the general properties of any wood you are buying, especially if you want to stain it later. Paint grade refers to low quality wood, for instance, while stain grade refers to better gain pattern used for staining. Veneer and particleboard are different too. Veneer doesn’t absorb stain and particleboard absorbs more. Using the proper wood makes sure that your project ends up the way you’d like it to.

Make sand blocks that you can reuse. Make a list of each sandpaper grit that you typically use, and then cut a full six blocks for each from scrap plywood, 3/4″ thick. Cut them to 2.5″ by 4.75″. You can secure the sandpaper better with an adhesive. Stick one block to your cork and be sure to cut your cork flush using a utility knife. Then, spray your sandpaper with adhesive and apply it to the cork. Cut the sandpaper flush and label each block.

TIP! Consider making your own sanding blocks that are reusable. Use your scrap pieces of 3/4″ plywood and cut as many blocks as you need for the sandpaper grits you use the most.

Make sure to use the right nails. If the nail is too large, you could end up with split wood. Conversely, if the nail is too small, it can’t penetrate deep enough in the wood to hold these pieces of wood together. Always try to pick the right size nail for your job.

Put extra spring in your grip. You might need the extra spring when you already have your hands full. It is sometimes hard to get these things open when you’re only using a single hand. You can make this easier. It’s a good idea to get all of your clamps assembled on a piece of scrap wood before beginning a glue-up project. They will be handy to grab with one hand as you need them.

You should use more than just tape measures. You are sure to find how useful story sticks are. You can always also just work into a cut gradually. Practicing on scraps first is a great way to try various fittings. If you have a variety of cuts, you won’t get bored.

Use stair gauges for crosscut guides. Clamp them to carpenter’s squares and be sure they match the runs and rises of the stair jacks. Mark the notches on your carpenter’s square. Put them on your carpenter’s square guide for a great cut.

TIP! Try using a stair gauge as a crosscut guide. Clamp them to a carpenter’s square while making sure they line up with the rise and run of your stair jack.

It may seem fun to have a beer or two while working in the shop. That said, it isn’t good to imbibe if you plan to work with power tools. Avoid drinking alcoholic beverages while working with tools. Common sense also says to stay away from using any drugs, prescription or otherwise, for the same reasons.

Drafting Square

For more accurate smaller cuts, get a drafting square. If you have a cut that needs to be done and exceeds a couple feet in length, you will likely find it hard to do perfectly. Some people try to use drywall or carpenter squares for this, but both can prove to be inaccurate or difficult to manage. A drafting square from your art store works great! These are made for smaller measurements, making them very accurate and easy to use.

Know how much you can spend in order to create a project. It is quite common to be far more ambitious than the budget allows when working on a particular project. You may be excited to create start a new project, only to be disappointed half way to completion when you run out of funds. Plan things out in advance, and you won’t have unpleasant surprises.

TIP! Have a budget before beginning any woodworking project. Many people are surprised at how much it costs to make some woodworking projects.

Don’t create a type of extension cord octopus when woodworking. Only use one extension cord. Plug in only the tool that you are using and leave the rest unplugged. Reduce the risk of tripping over cords or the possibility of a nasty shock with this basic safety procedure.

Prepare wood before staining it. You can do this by using pre-staining conditioner. Wood conditioners soak right into the wood grain, helping the wood to evenly soak in the stain. Lastly, after your stain is on, use a rag to remove excess product.

Think about the future when you plan a big project. For instance, if a shed building project is being considered, is electricity something you may want in the future? If that is the case, make certain to have enough room for all the required switches and wiring.

Keeping a small ruler with you in a pocket is a great idea, however it may fall out easily because of its length. Purchase a metal ruler to carry along with a small telescoping magnet that is used to grab loose screws or nails. The magnet will ensure that the ruler won’t fall out.

TIP! While you might like keeping a small ruler handy in your pocket, you probably find that it falls out every time you bend over. Instead of wood, choose a metal rule and keep it with your magnet.

Never over-purchase when buying building supplies. When you have too much, you might not use all of it, so buying everything in bulk could mean that you have too much to store. Instead, buy just want you need now and the things you know you’re going to actually use in the immediate future.

Use the sharpest blades you can. A lot of accidents in woodworking are because blades are too dull. Dull blades can cause wood to kick back on a table saw. This kickback has been the cause of many workshop accidents. Also you should be sure you have razor sharp drill bits for better results.

Prior to cutting wood, carefully look for nails or screws within it. Even new lumber could have some left over metal in it from tags attached at the store. Sometimes, wood is joined with stapled bands and can stay in the wood, which could cause injury.

Before using wood, make sure you have a good grasp of all the different types of woods that are out there. Each type of wood has different traits. Different types of wood take stain differently. Also, different woods splinter differently when they are cut. Therefore, you will want to check out all of the types possible. All of these factors have an effect on your wood project.

TIP! Understand the properties of the wood you’re using. Each wood has its own characteristics.

Woodworking skills can be acquired. Fabricating something from beginning to end is a terrific feeling. No matter what you come up with, the right knowledge is helpful when you’re going through the steps to complete the project. Why not make a birdhouse? It doesn’t have to be a useful item!