If you want to learn more and enhance your woodworking skills, this is the right article for you! The article below is full of great tips for people at every skill level. When you continue reading, you’ll learn a ton of new tips.

Try using a stair gauge as a crosscut guide. Clamp your carpenter’s square to your stair gauges while ensuring they coincide with the rise and run of your stair jack. After this, you will have to mark each of the notches. Putting them on the carpenter’s square tongue makes for a great guide for a circular saw.

Create sanding blocks you can reuse. First cut 6 blocks from scrap plywood, one for each grit of sandpaper you like to use. Be certain the pieces are about two and a half inches by four and three quarter inches. You can secure the sandpaper better with an adhesive. Place one block onto the cork and make sure the cork is cut flush with a sharp knife. After spraying adhesive on a sheet of sandpaper, place it on the block face of each cork. Finally, trim the sandpaper and label each block.

TIP! Try making sanding blocks that are reusable on your own. Start by cutting six blocks from scrap 3/4″ plywood for every sandpaper grit you generally use.

Gel stains are great for staining furniture. Gel stains adhere to wood better, while liquid stains run a lot more. Additionally, because gel stains are thicker the pigment remains consistent throughout the application allowing for more even staining on horizontal and vertical pieces.

Dry Fitting

Consider doing a dry fitting of your pieces before you use glue to join these together. You could cause damage if you tinker with the fit after you’ve applied the glue. Dry fitting the pieces together gives you an idea of what pieces go where.

Pick out the wood that’s right for your project you’re doing. Some pieces require a durable hardwood, while others can be done with a softer type of wood. Learn as much as you can about the different varieties of wood before beginning any woodworking project.

TIP! Pick out the right kind of wood. In woodworking, not every wood can sustain every type of stress.

A stair gauge is an essential item in every wood shop. They can layout stair jacks as well as clamp carpenter’s squares. This will turn your square in to a circular saw guide. This square will make sure your cuts are straight each time.

Get a handle on how a wood takes to staining prior to choosing a wood for a project. For instance, if a wood is paint grade, it’s probably not quality wood. Stain grade means the wood’s grain pattern makes it great for staining. Also realize that veneer and particleboard are different. Particleboard will absorb too much stain, veneer might not absorb enough. Choosing the right wood makes sure your project becomes all that you planned.

Keeping a small ruler with you in a pocket is a great idea, however it may fall out easily because of its length. Try switching to a metal ruler, keeping it in a pocket with your telescoping magnet, the kind used to reach and pick up screws or nails. This will hold the two together, making them bulking enough to stay put.

When you’re working out a budget, you have to think about itemizing the new tools you may have to purchase. A lot of woodworkers forget about the cost of new tools and focus on the cost of the piece of wood they want to work on. But, if new tools or materials will be required, your budget may be exceeded quickly.

Golf Tee

A golf tee provides a quick and easy fix for loose interior door hinges. Take the door from the hinges and tap your golf tee into every screw hole. Cut the excess, then put the door back on. The tee will allow the screw to bite into the door.

Choose correctly-sized nails. If a nail is too thick it can split the wood, and this will stop it from holding properly. However, very small nails do not penetrate well; therefore, they won’t hold the wood. It’s important to be able to match the correct size of nail for each job.

If you rent a tool that is unfamiliar, ask the rental company to give you a quick tutorial. A lot of the time they will have specialists that you can get help from so that you can be comfortable with how a tool works before using it. Also ask for any documentation to help you out.

TIP! If you’re looking to rent a tool you’ve never used before, ask for a tutorial before you leave the shop. The people that work for these companies have representatives well-versed in the tools they rent.

Add a bit more spring to your hand grip. You might need to use spring clamps, but you may only have one free hand. These clamps can be difficult to open without the use of both hands. However, it can be made easier. Prior to doing a glue-up, put your clamps on scrap wood with both hands. That allows you to pop them off and use them with one hand.

Are you having trouble reaching that out of the way and highly obscured screw? Look no further than your toolbox. Simply grab your screwdriver along with your 12 point socket. Attach the socket to the screwdriver and then to a ratchet.

Proper Lighting

Many people have a small ruler on them when working in the shop. Sometimes it will fall out of your pocket when you move around. Try switching to a metal ruler, keeping it in a pocket with your telescoping magnet, the kind used to reach and pick up screws or nails. The magnet will keep them both firmly inside your pocket.

TIP! It seems like a sound idea to have a small ruler within one of your pockets, but you are bound to discover that it falls out any time you bend over. To reduce this problem, you could get a metal ruler and put the ruler in the same place as where you store your magnet.

You should work in a well lit area. Accurate measurements are essential when woodworking. You will need a variety of sharp tools and proper lighting is needed to see what you are doing. If you do not have the proper lighting in your workspace, then you risk making mistakes or getting inured.

Go to yard sales, garage sales, and online to get better deals on woodworking equipment. This is a great way to find good deals. This can save you money when building your workshop.

Stay safe when using a table saw. When you are crosscutting, be sure to set the length of the cut using a block that is clamped onto the fence. This is a great tactic to help prevent the board from jumping back at you. Using this clamping method will allow the board end to still be cut.

Get proper size nails for your jobs. Any nail that is way too big in its diameter will split your wood a lot of the time and that makes it not hold right. Nails that are too small may not hold wood together. You need to identify the proper size for your project.

TIP! Don’t simply buy one-size-fits-all nails for your woodworking projects. If you use a nail whose diameter is too great, it can split the wood, which causes it not have a proper hold.

Make sure you have enough lighting in your wood shop. Whenever you have to sand, paint or stain anything, you need a lot of light. You will be able to see exactly where you will need to sand more. In addition, extra lighting is going to help you make sure that you apply your stain evenly.

Measure twice and cut once is an old adage that should be followed. Materials are expensive, so you might even prefer to check them three times. Poor measuring is typically where the most expensive errors happen. An error in length or angle can destroy the wood you needed for your project.

Power Sander

Look for free wood sources. A lot of places have unwanted pallets. Before you tear the pallets apart, you may want to look online at all the furniture and other building ideas using recycled pallets.

TIP! You should keep an eye out for free wood around your area. Some businesses toss out old pallets and wood scraps they do not need anymore.

Power tools are a must in a shop. If you don’t already have them, purchase a circular saw, jigsaw, small table saw, power sander, and a good drill or driver. While an orbital sander would be ideal, any power sander will do.

Before beginning a project, know what you are doing. Surely you don’t want to make mistakes. Instead, read over any directions multiple times to ensure you completely understand the steps you must take.

Think about future modifications when planning a big project. For instance, if you are constructing a shed, will you want it to have power at some point? If this is the case, make sure that you leave enough room to wire it for electricity and plan for places to install lights.

Use recycled wood. Some woodworking shops discard useful scraps. Home improvement centers and flooring stores often discard unused wood. Use this to your advantage and keep an eye out for pieces you can use. This can also save you quite a bit of money in the long run.

As was mentioned earlier, the tips learned here will assist a woodworker of any level. Apply this knowledge to your next project. Now get started!